自上料攪拌車有哪些常見故障要知道的
自上料攪拌車是生產混凝土的主要設備，如果混凝土攪拌機出現故障，就無法生產混凝土，也會耽誤工程的運行，自上料攪拌車常見的故障有哪些？下面自上料攪拌車廠家為您講解。
The self loading mixer is the main equipment for concrete production. If the concrete mixer fails, it will not be able to produce concrete and will also delay the operation of the project. What are the common failures of the self loading mixer? Next, the manufacturer of the loading mixer will explain it to you.
電機或減速機過熱。自上料攪拌車出現電機或減速機過熱現象時，應該對電機與減速機的膠帶輪進行詳細檢查，觀察他們是否共面，三角膠帶的張緊是否還正常，有沒有其他的外力造成有額外負載；
Motor or reducer overheating. When the motor or reducer of the feeding mixer is overheated, the belt pulley of the motor and reducer shall be checked in detail to see whether they are coplanar, whether the tension of the V-belt is normal, and whether there is additional load caused by other external forces;
其次對電機或減速機的表面進行檢查，觀察是否有覆蓋物在上面，從而導致溫度不能正常散熱；在對平行軸裝式斜齒輪減速機的油進行檢查，觀察油位是否正常，特別是潤滑油有沒有被污染，一旦有這些現象的出現，就要按照相應的標準要求進行加油或換油。
Secondly, check the surface of the motor or reducer to see if there is any covering on it, which may lead to abnormal heat dissipation; Check the oil of parallel shaft mounted helical gear reducer to see whether the oil level is normal, especially whether the lubricating oil is polluted. Once these phenomena occur, oil shall be added or replaced according to the corresponding standard requirements.
當然自上料攪拌車的漏斗是需要我們進行及時清理的，如果我們清理不及時就回去導致我們的物料輸送不流暢，導致攪拌裝置發生故障時，要及時的減修復。
Of course, we need to clean the hopper of the feeding mixer in time. If we do not clean it in time, we will go back to the mixer, causing our material delivery to be not smooth, which will lead to the failure of the mixing device, we need to repair it in time.
對于司機來說，我們應該進行正規化的擦走，即使是在下班的過程中，我們也應該進行淡定的配合，當完成澆筑任務時，操作工壓迫采取相應的配合，保證在收回布料桿，在進行停止我們的工作。
For the driver, we should carry out standardized wiping. Even in the process of getting off work, we should also carry out calm cooperation. When the pouring task is completed, the operator should press and take corresponding cooperation to ensure that we can stop our work when the boom is withdrawn.
自上料攪拌車在進行生產的過程中，我們應該充分的根據我們的操作和相關的操作經驗進行操作，防止操作失誤，影響我們的工作。
In the process of production of self loading mixer, we should fully operate according to our operation and relevant operating experience to prevent operation errors from affecting our work.
自上料攪拌車生產完成后需要人員定期進入清理，此是比較危險的作業，常出現工傷事故，進入主機內一定要先拉閘，確定停電后再作業。更多相關注意事項就來我們網站http://pheenet.cn進行咨詢了解吧！
Since the completion of the production of the loading mixer, personnel are required to enter and clean it regularly. This is a relatively dangerous operation, and industrial accidents often occur. When entering the main machine, you must first pull the brake, and then work after confirming the power failure. More relevant precautions come to our website http://pheenet.cn Consult and understand!
