自上料攪拌車廠家的調音臺軌道是什么？
調音臺軌道必 須為所有人所熟知。攪拌車被用在很多地方，攪拌車也起著非常重要的作用。當使用小的混合器軌道，例如混合器軌道時，總是出現相應的問題。一些小型攪拌車司機報告說，與朋友在同一時間購買同一輛攪拌車在使用汽車一段時間后會導致引擎問題，但是朋友車中的引擎很好。..發生了什么？發生了什么？混合器引擎為什么會這么快破裂？讓我們看看是否使用不當或車輛本身有問題。
The mixer track must be well known to all. Mixer truck is used in many places, and mixer truck also plays a very important role. When using small mixer tracks, such as mixer tracks, corresponding problems always occur. Some small mixer drivers report that buying the same mixer at the same time with friends will cause engine problems after using the car for a period of time, but the engine in friends' cars is very good What happened? What happened? Why did the mixer engine break so quickly? Let's see if it's not used properly or if there's a problem with the vehicle itself.
1.混凝土自上料攪拌車的維護數據使用不當
1. Improper use of maintenance data of concrete self loading mixer
在攪拌車的維護中，無法科學地選擇維護數據是零件過早損壞的重要原因。例如，對于進氣門，氣門與氣門座之間的接觸表面的寬度指定為1.2.2毫米，對于排氣門，規定為1.5.2.5毫米，但是在實際維護中，該寬度大于較大的寬度。需要這樣做。寬度很窄。
In the maintenance of mixer truck, the failure to select maintenance data scientifically is an important reason for premature damage of parts. For example, the width of the contact surface between the valve and the valve seat is specified as 1.2.2 mm for the inlet valve and 1.5.2.5 mm for the exhaust valve, but in actual maintenance, the width is greater than the larger width. This needs to be done. The width is very narrow.
許多人說這很好，通常將上限選擇為上限或接近上限。新修汽車的閥門工作表面的寬度已經接近其使用極限，因此這是上限。另一個例子是閥腳間隙。車輛通常指定為0.2-0.25毫米。但是，維護調整認為該間隙大于較小的間隙。因此，如果間隙超過上限，則間隙實際上太大，這不僅降低了發動機功率，而且由于沖擊而引起了初始損壞。
Many people say this is good, and usually choose the upper limit as the upper limit or close to the upper limit. The width of the valve working surface of the newly repaired vehicle is close to its service limit, so this is the upper limit. Another example is the valve foot clearance. Vehicles are usually specified as 0.2-0.25 mm. However, the maintenance adjustment considers that the clearance is larger than the smaller clearance. Therefore, if the gap exceeds the upper limit, the gap is actually too large, which not only reduces the engine power, but also causes initial damage due to impact.
2.平穩地壓碎混凝土自上料攪拌車的閥門
2. Stably crush the valve of concrete self loading mixer truck
為了保持較小的混合器軌跡，如果閥門有消融，凹坑或凹痕，通常需要使用拋光研磨機對其進行拋光。在操作過程中要注意四個問題。，檢查閥頭和閥桿。同心圓，否則您需要先修復它們。接下來，假設您可以拋光的圓錐，則需要使光滑的汽車盡可能小。接下來，您需要進行表面拋光。第四方面應盡可能提高以平滑閥桿的凹入端。
In order to maintain a small mixer trajectory, if the valve has ablation, pits or dents, it usually needs to be polished with a polishing grinder. In the process of operation, we should pay attention to four problems. First, check the valve head and stem. Concentric circles, otherwise you need to fix them first. Next, suppose you can polish the cone, you need to make the smooth car as small as possible. Next, you need to polish the surface. The fourth aspect should be raised as much as possible to smooth the concave end of the valve stem.
