混凝土攪拌車卸料時的注意事項！
中科聚峰攪拌車卸料環節其實對于工程的建設進程是很重要的，卸料慢的話會浪費很多的時間，像一般卸料慢的大部分都是小型攪拌車，那只是因為它放量小才卸料慢嗎?當然不是，攪拌車卸料慢跟液壓泵和液壓馬達有關，一般小型攪拌車的液壓馬達都是定量齒輪泵，它的工作速度不怎么快，就是加油門也不會有明顯改善，而且還不能長時間的加大油門會燒壞齒輪油泵。下面我們就來了解一下混凝土攪拌車卸料注意事項。
In fact, the unloading link of concrete mixer truck is very important for the construction process of the project. If the unloading speed is slow, it will waste a lot of time. For example, most of the slow unloading parts are small-sized mixer trucks. Is it only because of its small volume that the unloading is slow? Of course, it is related to the hydraulic pump and hydraulic motor. Generally, the hydraulic motor of small mixer truck is fixed displacement gear pump, Its working speed is not very fast, even if the fuel door will not be significantly improved, and also can not increase the throttle for a long time, it will burn the gear oil pump. Next, we will learn about the concrete mixer truck unloading precautions.
1、卸料前讓攪拌罐全速運轉一兩分鐘。讓混凝土充分攪拌，必要時可以加一些水，讓混凝土攪拌得更均勻，也方便卸料。
1. Let the mixing tank run at full speed for one or two minutes before discharging. The concrete can be fully mixed, and some water can be added if necessary to make the concrete more uniform and convenient for unloading.
2、放料前先把出料斗溜槽打濕。放料時把車盡量停在平地上放料前先把出料斗溜槽打濕，方便清洗。
2. Wet the discharge hopper chute before discharging. When discharging, park the truck on the flat ground as far as possible. Before discharging, wet the discharge hopper chute to facilitate cleaning.
3、卸料不要大意和放料工打好關系。放料時盡量自己看著，免得放料工亂操作放料操作桿，每次罐子正反轉中間位子時要停一下，保護減速機，托輪等。與放料工打好關系，卸料時也不要睡的太熟，萬一工人鬧情緒，把你車子放到工地不轉罐子，造成悶罐就麻煩了。
3. Don't be careless in discharging materials and have a good relationship with the discharging workers. When discharging materials, try to watch by yourself, so as to prevent the discharging workers from operating the discharging operating rod disorderly. Stop every time the middle position of the tank is in the forward and reverse direction, so as to protect the reducer and supporting wheel. Make a good relationship with the discharging workers, and don't sleep too well when unloading. In case that the workers are in a mood and put your car on the construction site without turning the cans, it will be troublesome for the cans to be stuffy.
4、攪拌罐一定要仔細地沖洗干凈。洗罐子時一定要仔細的沖洗干凈，并把水反復的正反轉兩次，再放出來，然后一趟時把水箱的水全部放進罐子，再回到站加水清洗罐子。
4. The mixing tank must be washed carefully. When washing the tank, be sure to wash it carefully, and turn the water forward and backward twice, and then put it out again. Then put all the water in the tank into the tank, and then return to the station to clean the tank with water.
5、之后別忘了施工單位簽字。把到工地時間和自己的大名簽上，別忘了施工單位簽字，否則白干了。
5. After that, don't forget to sign by the construction unit. Sign the time of arriving at the construction site and your name. Don't forget to sign by the construction unit, otherwise it will be in vain.
6、在施工現場卸料完畢后，應立即用攪拌車隨帶的軟管沖洗進料斗、出料斗、卸料溜槽等處，粘附在車身各處的污泥及混凝土。在返回攪拌站的途中，應向攪拌筒內注150---200L水以清洗筒壁及葉片粘結的混凝土殘渣。
6. After unloading at the construction site, the inlet hopper, discharge hopper and discharge chute should be flushed with the hose attached to the mixer to remove the sludge and concrete adhering to the vehicle body. On the way back to the mixing station, 150-200l water should be injected into the mixing drum to clean the concrete residue bonded by the cylinder wall and blades.
7、每天工作結束后，司機應負責向攪拌筒內注入清水并高速（14—18轉/分）旋轉5—10分鐘，然后將水排去，以保證筒內清潔。用高壓水清洗攪拌筒各個部分時，應注意避開儀表及操縱桿等部位。壓力水噴嘴與車身油漆表面間的距離不得小于40厘米。
7. At the end of each day's work, the driver should inject fresh water into the mixing drum and rotate it at high speed (14-18 RPM) for 5-10 minutes, and then drain the water to ensure the cleanness of the drum. When cleaning each part of the mixing drum with high pressure water, pay attention to avoid the instrument and control rod. The distance between the pressure water nozzle and the paint surface of the vehicle body shall not be less than 40 cm.
